Brands Hatch Performance Limited
Cart 0
Link G4+ Monsoon ECU Ford RS Cosworth YB engine Kit with Wiring Loom & Bosch 550cc / 1000cc Injectors & K20 Coils

Link G4+ Monsoon ECU Ford RS Cosworth YB engine Kit with Wiring Engine Loom & Bosch 550cc / 1000cc Injectors & K20 Coils

£2,000.00

At BHP we have spent a long time perfecting the installation of Link ECU's into Cosworth YB Powered Cars including the Sierra & Escort RS Cosworth and a multitude of RWD cars (Mk1/2 Escort, Capri's, Anglia's plus some very odd vehicles)

We have now put together definitive kits to bring your YB up to date with a new Link G4+ ECU. The ECU will run individual injector and ignition trim, plus a selection of optional motorsport features like Launch control and Anti Lag. The Link ECU will also come with much better engine protection, which is what is very lacking in the standard Weber, thats pretty much why the engine becomes unreliable when tuned . 

The Cosworth Loom kit includes the following: Link G4+ Monsoon ECU With on Board 4 Bar Map Sensor, Base Map,  Full engine loom,  4x BOSCH 550cc or 1000cc Injectors Mulithole Injectors With Height Adaptors , 4x Honda K20 coil's with mounting brackets, Distributor cover & Boost Controller with bracket.

The Kit we are selling is a comprehensive kit and allows you to sell the following items (Dependant on ECU) to help fund the new install:
ECU, Loom, Ignition Amp & bracket, Ignition Leads, Injectors, MAP Sensor & bracket & AMAL Valve. This can add up to quite a lot of money nowadays making this kit very cost effective.

Link G4+ Monsoon ECU Specification:

The Link G4+ Monsoon is a step up from Link Engine Management Entry Level Atom ECU with some extra features including Onboard 4 bar MAP sensor & Motorsport features such as Gearshift control , Launch control, Anti Lag, VVT Control and Closed Loop Boost Control.

The Monsoon ECU can run any of the above motorsport features however not all at once; it is dependant on the number of limited inputs and outputs the feature needs.

The Link G4+ Monsoon ECU runs the same microprocessor & firmware as the Link G4+ Xtreme. It is fully configurable with no preset Inputs / Outputs, has 32Mb of  Logging Memory, Motorsport features and closed loop fuel if an external device is added e.g Wideband controller.  

The Link G4+ Monsoon ECU has a 34 pin Waterproof Connector, mounting bracket and USB tuning cable & Link Stickers 

Engine Configurations:

2-12 Cylinder Distributed

2-8 Cylinder Wasted Spark

2-4 Cylinder Direct Spark

Odd Fire Engines

2 Stroke Engines

Configurable Firing Order

Configurable TDC Points (for odd Fire)

Inputs:

4 x Digital Inputs (e.g Vehicle Speed & Logging Switch etc)

2 x Temperature Inputs  (e.g Water & Inlet Air Temperature etc)

4 x 0-5V Analog Volt Inputs (e.g Oil Pressure etc)

2 x Trigger Inputs

Outputs:  

4 x Injector Drives

4 x Ignition Drivers

6 x Auxiliary Outputs* (e.g Fuel Pump , Fans , Boost control , 02 Heater etc)

+5V Sensor Power Supply

*Unused ignition drive can be used as auxiliary outputs

Communications:

1 x CAN Bus

1 x Thirty Four pin Waterproof Connector

1 x USB tuning connection

Misc:

Onboard 4 Bar Map Sensor

Onboard Barometric Pressure Sensor

VVT Control

32Mb (4 MByte) of logging memory

20 general purpose tables

Runs on PC Link software

More Details found here: https://shopbhp.com/products/link-g4-m-monsoon

 The ECU also features the ability to run a windows 10 tablet (£125 Amazon) for tuning, diagnostics and just to use as a Dash. The CAN output can run a standard ISO diagnostic port just like a modern car.

Link ECUs also come with a LIFETIME Warranty! 

Cosworth Engine Loom Specification:

AVSS Automotive thin-wall wire used throughout and genuine TYCO and DELPHI Connectors.

Loom will be supplied braided and labeled as per the photo and compete with high quality 60mm bulkhead grommet. (Heat-shrink Finish Available if Preferred)

Loom comes standard with:

  • New Panasonic micro relays.
  • New BHP Standard Multiway Delphi Body Connector, with spare ECU connections terminated.
  • ISO OBD2 CAN Output (to connect standard OBD2 diagnostics / Tablets and Mobile Devices)
  • Fuel Pressure Connection where applicable.
  • Oil Pressure Connection where applicable.

 All looms are made to order and as such can have extra wires added cost is £25 per wire.

Extras can Include:

Drive By Wire Throttle (E-Throttle) (Xtreme)

Wideband Lambda Sensor (Fury and Thunder)

Knock Sensor (Storm, Xtreme, Fury, Thunder)

Fuel Pressure

Sump Pressure

and many more possibilities

Looms are made in batches and can take up to 10 working Days to complete. 

You will need to contact us once purchased to ensure we have correct configuration noted for your loom. 

Please contact us to discuss any other technicalities we have not covered.

We also have a Kit based around the Link FURY ECU which can include Drive by wire throttle which maximises engine torque, enables speed limit and cruise control, and loads of additional sensors can be added for both precise control and safety. Due to the specification of this kit we run this with one of our project specialist so contact us for more information.

Fitting and Mapping also available! - Call us to discuss. 

0% interest Free Finance Available! 

Any Questions give us a call on 01474850666!


Share this Product


More from this collection